RTS TM-2000 Instrukcja Użytkownika Pobierz pdf (Strona 27)

7 Installation Notes

7.1 General Installation Procedure

These are the steps that you should generally use to get

your Zeus intercom system up and running.

1. Unpack and inspect the equipment.

2. Organize a set of equipment manuals. (You may have

several copies of some types, keypanel manuals, for

example.)

3. Mount the Zeus frame and connect it to the

configuration computer.

4. Install ZEUSedit on the configuration computer.

5. Log on to Zeus from ZEUSedit.

☞

You may wish to run the 1studio.zus example and

take a few minutes to familiarize yourself with the

software (recommended).

6. Begin connecting keypanels and other components.

Verify operation of components as they are

connected.

7. Configure the intercom system using ZEUSedit.

Perform periodic downloads to check progress.

8. When you finish naming things, you can print out the

name lists and distribute them if desired. KP95-0

Keypanels: When you finish assigning keys, you can

print out designation strips, cut them to size, and

insert them into the holders on the KP95-0 keypanels.

9. Perform any input and/or output gain adjustments for

any audio devices that are operating at non-standard

levels. (Use this adjustment when the level for a

particular device needs to be adjusted throughout the

intercom system.)

10. Adjust any crosspoint and party line gains as needed.

(Use these adjustments when you want to adjust the

mix for individual users.)

11. Set up dim tables as required if there are any

feedback problems between intercom stations

operating in close proximity to one-another.

12. This completes the general installation procedure.

You may also wish to make use of the Logging and

Partial Save features of ZEUSedit. Logging is

available on the Logging menu. Logging basically

keeps track of key activations, which can sometimes

be useful for diagnostic purposes. Partial Save is

available on the File menu. Partial Save lets you set

up configuration files to make routine changes to

portions of your intercom system setup.

7.2 Unpacking the Equipment

As soon as possible after receipt, inspect the container(s)

and contents for physical damage that may have occurred

in shipping. If damage has occurred, immediately (within

24 hours of receipt of equipment) contact the carrier in-

volved and file a claim. Save all packing materials, and

request an immediate inspection by the carrier’s insurance

claims agent. Refer to the equipment manuals for each

item for any information about items packed with that

equipment.

☞

For information about returns to RTS, refer to the

front of this manual.

7.3 Zeus Mounting Precautions

☞

Important! Leave at least 1 rack unit of space

above and below Zeus and do not obstruct the

cooling vents at the sides. Also, do not mount Zeus

near any other component that generates an unusual

amount of heat.

7.4 AC Power Connection

1. Place the AC switch on the back panel in the off (O)

position.

2. Connect the AC power cord.

7.5 Computer Connection

1. Turn the computer off.

2. Connect the computer cable to J25 on the back of

Zeus.

3. Connect the other end of the cable to any available

COM port on the computer. The COM ports may be

labeled COM 1, COM 2 etc. and may also be

identified by any of the following symbols.

☞

If you need a longer computer cable, you can

construct one using Figure 15, page 23.

Getting Started, Zeus™ DSP Intercom Matrix 25

COM port symbols

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 36 37

Komentarze do niniejszej Instrukcji

Brak uwag

RTS TM-2000 Instrukcja Użytkownika Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Domofony RTS TM-2000